Smart Thermostat Installation and Repair in Fort Worth
A new thermostat only helps if it talks to your furnace, heat pump or AC the right way. Our techs check the wiring and the equipment behind it, install the control, and show you how to run it.
Request Service
Tell us what's going on and the office will call you back to set a time.
Rather pick a time yourself? Book online
Thermostat
What does a thermostat installation include?
A thermostat chosen for your equipment, wired and tested in heat and cool. The tech first checks what’s behind the wall plate: a gas furnace or heat pump, one stage or two, and whether a common wire is there for a smart model. Then the new control goes up, each wire lands where it belongs, and both modes run.
- Smart and Wi-Fi thermostats, Nest included
- Programmable thermostat upgrades
- Controls set up for heat pumps and dual-fuel systems
- Blank screens and settings that won’t hold
- Communication errors between the thermostat and outdoor unit
- Common-wire and thermostat wiring fixes
- Calibration checked during heating tune-ups
- Help learning the app and schedule
Good to know
Is the problem the thermostat or the system?
Often it’s the system, so check before buying. A blank screen, settings that won’t hold or a reading that’s off from the room point at the thermostat or its wires. A unit that runs but blows warm air usually doesn’t. Jan N. wrote “I thought I needed a new thermostat,” and the tech found the unit low on refrigerant.
Before the thermostat visit
- Pull the face off the old thermostat and photograph the wires and the letters beside each one.
- Write down the model numbers on your indoor and outdoor units, if you can reach the labels safely.
- Bought a smart thermostat already? Keep the box, and have the Wi-Fi name and password ready.
- Note the symptom: a blank screen, short cycling, the wrong temperature or an error code.
- Call (682) 474-0599 or book online, and say whether you have a heat pump or a gas furnace.
The rules
What does the ENERGY STAR mean on a smart thermostat?
It means the savings were measured in lived-in homes, not a lab. ENERGY STAR’s criteria have makers pool a year of data from hundreds of customers’ homes and show a run-time cut of at least 8% for heating and 10% for cooling, after a statistical margin comes off the weighted national average.
10%the least cooling run-time cut an ENERGY STAR smart thermostat must show across real homes
Those numbers come from ENERGY STAR’s smart thermostat key product criteria. Its smart thermostat buying advice adds two practical points: confirm the model works with your system before you buy, and for very high-efficiency equipment, consider the manufacturer’s own control. The Department of Energy puts the payoff of a schedule plainly: you can save as much as 10% a year on heating and cooling by turning the thermostat back 7 to 10°F for 8 hours a day.
How the visit runs
How a thermostat visit runs
- Book a timeCall the office or pick a slot online through Housecall Pro, and a reminder text follows.
- Check the systemThe tech identifies the equipment and its stages, then tests the wires at the wall and the board.
- Options and priceYou hear which thermostats will work with your system, and what each costs, before anything goes up.
- Install and testThe new thermostat is mounted, wired and run through heat, cooling and fan.
- Set it up with youWe go through the app and schedule together, and mention the Protection Club if a tune-up is due.
From a customer
What do customers say about their thermostat work?
David B. wrote that David did “an excellent job Installing my new nest thermostat” and had to troubleshoot it to get it connected. Riman C. needed help with a digital thermostat, and the tech “showed us how to use it.” Richard B. said Ezekiel explained everything, “Especially with the thermostat.”
“He was thorough and showed me why we were having all the problems with our unit. He did a great job explaining all of my options. And, he even had the thermostat I needed on the truck and was able to install it right then so we can have heat tonight”
FAQ
Thermostat Questions: Batteries, Wiring and Smart Models
Will a smart thermostat work with my heat pump?
Many will, as long as it’s set up as a heat pump control, with the reversing valve and backup heat on the right terminals. The Department of Energy notes that programmable thermostats generally weren’t recommended for heat pumps until makers began selling models built for them. Set up wrong, a deep overnight setback can bring on the electric heat strips on a cold Fort Worth morning.
My new thermostat says it needs a C-wire. Now what?
A common wire gives a smart thermostat steady power, and plenty of older North Texas homes have a thin cable with no spare conductor. The answer might be an unused wire already in the bundle, a new cable pulled from the air handler, which here often sits in the attic or a hall closet, or the maker’s adapter. The tech checks which one fits your system.
Where should a thermostat go on the wall?
On an inside wall, away from anything that fools it. A thermostat in afternoon sun, beside a supply vent, near the stove or across from an outside door reads the wrong temperature and runs the system too long or too little, which you feel in a 100°F July. Moving one means a new cable run and a small wall patch, so ask before you buy.
Does a tune-up include the thermostat?
The heating one does. Our 21-point heating tune-up includes thermostat calibration, along with the carbon monoxide test and the heat exchanger inspection, and you get a written system health report. Protection Club members get two 21-point tune-ups a year for $14.95 a month, with no contract, plus 15% off repairs.
Do high-efficiency systems need a particular thermostat?
Often, yes. ENERGY STAR suggests confirming compatibility first, and says very high-efficiency equipment may be better served by a control from the same manufacturer. Variable-speed and communicating systems can lose features on a generic thermostat. Bring the model numbers from your indoor and outdoor units, and we’ll tell you which thermostats fit before you spend anything.
Service area
Which towns can book a thermostat visit?
Thermostat calls come into two offices. The Fort Worth office on Golden Heights Rd covers far north Fort Worth, Keller, Watauga, North Richland Hills, Hurst and Haltom City, out to Arlington, Mansfield, Burleson and Weatherford. The Saginaw office on W Lemon St handles Saginaw, Blue Mound, Lake Worth, Sansom Park, Azle, Rhome and Roanoke.
- Fort Worth, TX
- Saginaw, TX
- Keller, TX
- Watauga, TX
- Blue Mound, TX
- Lake Worth, TX
- Sansom Park, TX
- Azle, TX
- Springtown, TX
- Reno, TX
- Rhome, TX
- Haslet, TX
- Roanoke, TX
- North Richland Hills, TX
- Haltom City, TX
- Southlake, TX
- Hurst, TX
- Euless, TX
- Bedford, TX
- Grapevine, TX
- Arlington, TX
- Mansfield, TX
- Burleson, TX
- Benbrook, TX
- Granbury, TX
- Weatherford, TX
- Crowley, TX
- Everman, TX
- Rendon, TX
- Joshua, TX
- Godley, TX
- Alvarado, TX
- Keene, TX
- Venus, TX
- All service areas
Related services
Other work that touches your thermostat
Talk to Eric's team
Thermostat acting up, or ready for a smart one?
Call (682) 474-0599 or book online, and the tech will check the wiring and the system behind it before recommending a new thermostat.

